Pages: [1]   Go Down
  Print  
Author Topic: Aria Pro II Wiring  (Read 4751 times)
0 Members and 1 Guest are viewing this topic.
casey47
Newbie
*

Thanked: 0
Offline Offline

Posts: 2
Referrals: 0


View Profile
« on: April 12, 2010, 03:53:27 am »

Does anyone know where to get a wiring schematic for an Aria Pro II RS 600 guitar
Logged
Share This Topic:  
Shawnvs
Newbie
*

Thanked: 1
Offline Offline

Posts: 96
Referrals: 0


View Profile
« Reply #1 on: April 12, 2010, 05:47:08 am »

have you got a pic of the guitar?
Logged
Alan Ratcliffe
Administrator
*

Thanked: 418
Offline Offline

Location: Near Cape Town
Posts: 15,452
Referrals: 73



View Profile WWW
« Reply #2 on: April 12, 2010, 09:08:13 am »

I don't have a schem, but I know the ST1512 and the RS600H (humbucker version of the 600) quite well. I'm looking for an RS600 myself Smiley. My favourite through necks...

Note on the 600 that the middle pickup is a "slave" - it's a noise cancelling coil, like on the alembic guitars. The pickup selector is a three way rotary for the two single-coil pickups. I'm not sure what the mini toggle on the 600 does (Aria called it a "mix sound" switch) - probably a series/parallel for the middle switch position.
Logged

WWW.GUITARFORUM.CO.ZA
**************************
Guitars: Ratcliffe Strat, Carvin NS-1, PRS SC245, Dean Sarasota 12, Sanox, Hohner Jack Bass, Alvarez 5056
Amp: '63 Fender Twin Reverb
Rack: Avid 11 Rack, TC G-System, Lexicon MPX550, Fishman Aura DI, Adrenalinn II, Focusrite Liquid 56, Samson PB-10, Digitech Live Pro
Floor: TC G-System, Roland GR-55 Guitar Synth, Roland TD-9, 2 x Roland KD-9 kick triggers
casey47
Newbie
*

Thanked: 0
Offline Offline

Posts: 2
Referrals: 0


View Profile
« Reply #3 on: April 13, 2010, 06:48:55 am »

My problem is that the three wires are broken off at the rotary switch pins and I can't tell which wire goes where. The broken wires are red white and green.

The switch is P/N Mr-3-3 which has 12 pins grouped in sets of three marked 1C, 2C, and 3C, and three unmarked pins in the centre. Two of the centre pins are soldered together,  the 2 and 3 pins of 1C group are soldered together, and pin 1 and 2 of 2C group. It is obvious that the wires were attached to the pins that are joined together.

If someone has a guitar with the rotary switch, perhaps they take a peek at the switch wires for me?

Logged
Paul E
Hero Member
*

Thanked: 27
Offline Offline

Location: Ballito, durban
Posts: 1,778
Referrals: 1



View Profile
« Reply #4 on: April 13, 2010, 08:24:30 am »

Where do you live?
Logged
Alan Ratcliffe
Administrator
*

Thanked: 418
Offline Offline

Location: Near Cape Town
Posts: 15,452
Referrals: 73



View Profile WWW
« Reply #5 on: April 13, 2010, 09:49:34 am »

You're in luck - I still have one of those switches (Fujisoku). I'll take a look and let you know.

...Actually, I don't need to - from what you have described it's easy to figure out.

One of the three wires will go to the master volume control on the other end. That will go to the pins joined together in the middle.

The other two wires will each go to a tone pot and pickup at the other end. Each of those wires must be soldered to one of the joined pair of outside pins on the switch. Just solder one to each and if the switch works backwards from how you want it, just swap the two wires around.
Logged

WWW.GUITARFORUM.CO.ZA
**************************
Guitars: Ratcliffe Strat, Carvin NS-1, PRS SC245, Dean Sarasota 12, Sanox, Hohner Jack Bass, Alvarez 5056
Amp: '63 Fender Twin Reverb
Rack: Avid 11 Rack, TC G-System, Lexicon MPX550, Fishman Aura DI, Adrenalinn II, Focusrite Liquid 56, Samson PB-10, Digitech Live Pro
Floor: TC G-System, Roland GR-55 Guitar Synth, Roland TD-9, 2 x Roland KD-9 kick triggers
Pages: [1]   Go Up
  Print  
 
Jump to: